Pipe & Fittings

VEVOR Fittings and Pipes for Water, Air, and Irrigation Systems

Need to fix your plumbing, remodel, or install something new but aren't sure what parts you need? With VEVOR fittings and pipes, you can run a hot-water line, connect a sink, or set up a drip system with connections that will not leak and will last for years. Our catalog includes a wide range of sizes and materials, so you'll find the right parts for any job at home or on the job site.

Shop Fittings and Pipes by Fitting Type and Application

Looking for fittings and pipes by material and connection type is the fastest way to find the right parts. VEVOR sorts its catalog by fitting style, which makes it easy to match the right part to the job at hand.

PEX Tubing and Fittings

Today, flexible PEX is the common choice for water supply lines, and VEVOR offers a wide range of PEX tubing and pipes in standard sizes and diameters. PEX can bend around corners without extra elbows, meaning fewer joints and fewer potential leak points along a run. Our tubing works with three connection methods: crimp, clamp, and expansion, so you can use the tools you already have.

For hot and cold lines, radiant floor heating, and manifold systems, you can find both coils and straight sticks. Color-coded red and blue options make it easy to keep hot and cold runs separate behind the wall. When you build a system from these fittings and pipes, you get corrosion-resistant performance that will not scale or pit like older metal lines. For plumbers and do-it-yourselfers re-piping a home, PEX is a quick, affordable, and effective way to get water where it needs to go, with fewer connections to check later.

PVC and Vinyl Pipe Solutions

Rigid PVC is still a workhorse for drainage, waste, venting, and low-pressure uses. VEVOR sells PVC and vinyl tubing in a range of sizes, from washbasin drains to irrigation mains. Clear vinyl is great for moving fluids, aquariums, and workshop setups where you want to see the flow, while schedule-rated PVC handles pressurized cold-water lines.

PVC solvent welds into permanent, watertight joints in just minutes, which makes it a cheap choice for big runs. It also resists corrosion and chemical attack, which is why it shows up in pool plumbing, sprinkler systems, and utility drainage. When you plan these fittings and pipes for a project, match the pipe schedule and diameter to the flow and pressure you expect, then pair them with the correct primer and cement. VEVOR's PVC and vinyl selection is an economical, long-lasting option for both indoor drainage and outdoor irrigation, and the lightweight material makes handling and installation simple, even on big jobs.

Brass Pipe Fittings and Connectors

When you need something strong that can handle heat, brass is a top choice. VEVOR brass pipe fittings make joints for hot water lines, gas connections, and high-pressure systems that last and resist corrosion. Brass threads are great for valves, manifolds, and transition points because they seal well and can be assembled and disassembled many times.

For pipe fittings and connectors, we offer more than just brass. We have couplings, elbows, tees, unions, and adapters in the sizes that real jobs need. These parts let you change pipe type or direction without breaking the seal. To protect the whole system, use good fittings and pipes. One weak connector can ruin an otherwise strong installation. When you put brass on a potable water line, make sure it is lead-free to meet code. You can use VEVOR's tough, precisely machined connectors to connect copper to PEX or to an existing metal system. They thread smoothly and hold pressure for years of reliable service. 

Push-to-Connect and Quick-Release Systems

These days, the fastest way to work without tools is to use push connections. VEVOR's push-to-connect fittings quickly connect copper, PEX, and CPVC with just a push. No glue, clamps, or soldering is needed. An internal O-ring and grip ring make a watertight seal right away. Many are removable, so you can swap them out or reuse them while the repair is underway.

You can quickly separate and reconnect lines with our quick disconnect adapters for air lines, coolant loops, and equipment hookups. This lets you do it without draining the system. Use them for pneumatic tools, cleaning areas, and other places where you change connections often. Adding these fittings and pipes to your kit lets you make a strong joint even in a small, wet area. This saves time on service calls and emergency repairs. VEVOR makes these connectors to hold rated pressure while still being easy to release by hand. This gives professionals and homeowners a quick way to connect without sacrificing safety or leaks. 

Matching Fittings and Pipes to Size and Material Needs

Picking the right fitting style is only half the job; size and material keep the system from leaking. When you understand how fittings and pipes are measured and made, your parts will fit right the first time.

Getting the Size and Fit Right

Start with the part size when you buy it; a part that doesn't fit is the worst. All of VEVOR's fittings and pipes have clear diameter, thread, and length specs, so you can compare outside diameter, standard pipe size, and thread type before you buy. When you mix standards, like NPT threads with metric threads, leaks often happen, so make sure you check the spec on both sides of a joint.

Hardware that supports the run is just as important as the connection itself. The pipe clamps and other items we sell keep runs tight against walls, joists, and framing. This keeps your joints from sagging, vibrating, and stressing over time. Ample space between the clamps keeps long horizontal runs level and quiet. When you place your order, you can choose the joints, brackets, and end seals. You can also say whether you need slip or threaded ends. To avoid going back to fix problems, make sure the size and support are correct the first time. This leads to a cleaner, long lasting installation in any home or business. 

Choosing the Right Material for the Job

The materials determine how long a system will last and where it is safe to use. VEVOR uses materials like PEX, PVC, vinyl, brass, and more. Each suits different fluids, pressures, or temperatures. PVC and vinyl are great for drainage and cold runs, while PEX and brass are good for hot water. Push-to-connect parts let you connect different pipe types without special tools.

What moves through the queue and what is going on around it come to mind. Potable water parts must be lead free and NSF rated, while gas and high heat lines must be metal rated. For underground or outdoor runs, you need materials that will not rust or fade in the sun. For chemical transfer, use tubing rated for the fluid, and always check the material spec sheet. Choosing the right material helps you avoid early failures and costly repairs later. VEVOR offers a variety of materials at fair prices, so you can build a system that works well and meets the rules without overspending on parts you don't need. 

Why Choose VEVOR Fittings and Pipes?

VEVOR supports every connection, from the first cut to the final pressure test. Our fittings and pipes are built to last, tested for leaks and pressure, and priced to keep repairs and remodels affordable for both professionals and everyday homeowners. With clear specs, easy access to parts, and reliable after sales support, plumbing projects have never been easier. Check out the full VEVOR collection, compare sizes and materials for your system, and make sure you have every connector your job needs. Add your parts to the cart right now and build with confidence using VEVOR.

FAQs

What kinds of pipes and fittings does VEVOR have?

VEVOR sells PEX tubing, PVC and vinyl tubing, brass fittings, push-to-connect joints, quick disconnect adapters, and pipe clamps. This range covers water, air, drainage, and irrigation systems, so you can get most of what you need for a job in one place.

Can I mix PEX, PVC, and copper in one system?

Yes, as long as you use the right transition fittings. Push-to-connect and threaded brass adapters safely join different materials. For potable-water lines, always use lead-free parts, and make sure each fitting matches the pipe's size and standard.

Can you trust push to connect fittings for long-term installations?

Yes. Quality push to connect fittings hold the rated pressure and stay watertight for a long time without solder or glue. Always check the product's rating and your local code to confirm they are approved for use inside walls.

How do I pick the right pipe size?

On both sides of every joint, the nominal pipe size, outer diameter, and thread standard must match. To avoid leaks, check the spec sheet for pressure and temperature ratings and confirm whether the threading is NPT or metric before you buy.