Customer Reviews for VEVOR Paper Cutter 30.5 cm A4 Guillotine Paper Trimmer 400 Sheet Capacity Metal Base

I am very disappointed in this product! It has been delivered not as shown. It does not have an adjustable, locking paper bar as shown in the picture. Instead, it has a plastic angle with round magnets on one side to attached to the base of the cutter. This angle will easily move allowing paper to be cut at different unintended lengths

Não gostei nada do produto, pois não atende as minhas necessidades. A base aonde serve de trabalho para o papel não é como a da foto é um ferro com íman que não trás nenhuma estabilidade. A linha de guia de corte mal se vê. Produto extremamente caro para o que ele oferece.

Within 2x use the blade was blunt, the black plastic calibration bar wiggles 5mm in all directions so cutting is also very vague.

Product *works* out of the box, instructions were simple to follow, didnt actually need them to use. Safety mechanism failed within days, but that does not stop the tool from working. still functions as a cutter. Issues: 1. The fence that comes pre-installed on the base of the machine is not square to the cutting blade or the printed grid on the tool so cuts are never truly square, and this cant be adjusted as the fence sits in pre cut slots and the bolts are only there to lock it down. 2. The cutting stick that sits under the blade sits proud of the level of the base. so when the paper is sitting flat on the base of the machine, the edge being cut is slightly raised up. so once the cut has been made, if cutting "blocks" of paper, the cut is not vertically square as the paper has been skewed up. There are adjustment bolts that screw in underneath the rubber, but even backed all the way out/removed, it still sits proud. Overall the product is functional. If you are a hobbyist and don't need millimeter perfect angles/cuts, its perfectly adequate. But thats about as far it goes. Adequate.

Lieferung ist heute angekommen, pünktlich. Schachtel weist keine Beschädigungen auf. Beim Aufstellen fällt auf, dass die Schneidemaschine nicht gerade steht und wackelt. Jetzt fehlt doch bei der hinteren Ecke der Fuss, die Ecke ist verbogen und es sieht nach einem Sturzschaden aus. In der Schachtel befinden sich keinerlei Bruchteile des Fusses. Der schützende Sagex war vorhanden. Es sieht so aus, als ob beim Verpacken in China das Teil auf den Tisch geknallt ist, den Fuss verlohren hat und trotzdem eingepackt und verschifft wurde. Da staunt der Laie und der Fachmann wundert sich...

Dear Sir or Madam, I am writing to make a complaint about a paper cutter blade I recently purchased from your company. In general, the blade cuts well through about 90% of the sheet. However, in the upper corner—near the handle that is pressed to cut—the blade consistently fails to cut the last part of the paper. About 10 cm of the last two sheets are left uncut every time. Because of this, I have to finish the cut using scissors or a smaller cutter. This defect is causing constant interruptions in my work and is seriously affecting my productivity. I bought this product to speed up and improve my work, but due to this fault, it is not performing as expected. I feel disadvantaged by this issue and would appreciate a solution, such as a replacement, repair, or refund, according to your warranty or customer service policy. Thank you for your attention. I look forward to your response.

Très lourd donc on suppose du matériel de bonne qualité, mais pas de notice de montage, je n’ai donc pas su comment monter la protection bleue, et l’ai jetée à la poubelle car impossible de comprendre comment l’attacher au reste. Ensuite, la coupe n’était pas bonne au départ, il a fallu que je l’utilise quelquefois pour que la lame s’affûte un peu et coupe mieux. Enfin, à chaque coupe, le levier frotte contre une autre partie et la peinture du levier s’écaille, ce qui laisse des résidus noirs de peinture sur le plan de travail à chaque utilisation. La cale en plastique censée bloquer le papier en place ne colle pas complètement à la partie métallique, il y a un espace, ce qui fait que les feuilles en dessous de la pile passent en dessous de la cale. Si l’on ne vérifie pas avant de couper, on se retrouve à avoir des feuilles qui ne sont pas coupées à la même taille que celles du dessus.

The product I received does not match what was advertised. Several components are inferior—for example, instead of a fixed bar to stabilise the paper, it uses a magnetised bar that constantly shifts position. The biggest issue, however, is that it simply DOES NOT CUT PROPERLY. On the rare occasions it does cut, the results are inconsistent and it often fails to cut through the entire stack of paper. What makes this even more frustrating is that the product arrived with a sticker stating it had been tested at the factory. Given that it does not function correctly out of the box, that claim is difficult to believe. A product like this should arrive ready to use and perform its basic function without requiring manual adjustments. Instead, I had to hunt down a vendor video to find adjustment instructions, as no assembly instructions or instruction on how to adjust it was included in the box. Even after following those adjustments, the cutting performance remained poor and inconsistent. Save yourself the frustration and don't waste your time on this product. I will be seeking a refund.

Please be aware that vevor is advertising their old model paper trimmer. I received their 'new and updated' paper cutter that no longer has a slide & screw secured paper baffle (the bit that goes behind the paper stack) and instead it is swapped out for a little plastic pusher with magnets on the bottom (that are light weight and struggle to hold paper in a fridge, much less push /hold a stack of 400 sheets you are trying to cut) The blade has no adjustment, but the red bar under the blade is adjustable - Unfortunately it needs to be adjusted to much that the paper lifts up onto that bar, and cuts at a significantly bevelled edge (for under 200 sheets, it was about a 4mm difference between the top and bottom edge) The metal base plate was warpped. the 'saftey lever' has been swapped for a pull out bright red ball - So - If you have any wrist weakness this is likely much less suitable now than the displayed product. I was subject to ongoing ai/standardised messages saying that "it takes times for facts to be checked" and after admitting this was not the displayed item, offered a $75 refund. This was not appropriate as it is unusable for "quickly and precisely" " cut{ting} through up to 400 sheets at once" - I asked for collection to be arranged, and a full refund. A full refund did come through - but no pick-up was arranged, so... I got to work out how to dispose of this. Poor Product not fit for purpose, and poor customer service.

Das Gerät ist ok, die Genauigkeit läßt sehr zu wünschen übrig.